The antenna can actually not much different from the TV antenna that is often used to receive signals from stationsTelevision, like INDOSIAR, RCTI, SCTV, Trans TV, Metro TV and do not forget RBTV. It could be said antenna can onlyas a signal amplifier alone (there are other opinions ..?).Antenna cans is another if an alternative is destitute, is less money to buy pigs (pig tail) whichthe price is quite expensive, or less funds to create omni antenna or helical antenna.Is the location of your home close to the hotspot area, or you're a lazy, lazy out of the house, and onlyPC1 has not allowed for lifted up out of the room? If the answer is yes, then the antennacans suitable for you who have limited funds.Remember, make sure there are no significant barriers from your residence to the nearest access point. Usually wellantenna can be used for war (wardriving).
The tools necessary following are the steps that must be prepared before making the antenna cans.
1. A tin that has a 13.3 cm long and 10 cm diameter (grease or oil can also be used).
2. PCMCIA Card (if you use a laptop that has not completed the Wi-Fi 802.11 b or 802.11 g), which has
an external antenna.
3. W-Lan PCI Card Wi-Fi 802.11 b or 802.11 g (for those of you who use a PC, the card is plugged into a
PCI slot). 4. SMA connector (for connecting a cable connector with a PCMCIA card or PCI W-lan
card, usually
some type of PCMCIA is still using the model pigtail with connectors SMA, SMB, SMC or MCX.5. RG-58 coaxial cable whose length should be no more than 15 meters.6. N Plug Connectors (TNC Plug Connector RG 58 CRMPG) used for connecting to a cable.7. N connector (TNC Connector seal chassis).8. Bolts and nuts (to attach to the antenna connector N cans).9. Slabs of the roll diameter brass tube 2.5 to 4 mm, can also use copper wire
taken from electric cables
Preparation Assemble 1. Preparation of the necessary tools close to you and prepare everything properly. 2. Cut your cans if still exceeding 13.3 cm in length using a saw or knife (if there is no hacksaw), and create a hole using a screwdriver or a knife if there is no drill with distance from the edge (bottom of the can) 4.4 cm.
Size used following is the size that you can use to make the antenna cans taken from the site wire.less.dk2. But the needNote that for long cans are not considered here. You can use cans that have alength of more than 100 mm without having to cut
To obtain a more precise measure, you can use the software cantennator which can be downloaded forfree from the internet (use google and then type the keyword "cantennator".Here is an example calculation using the cans with a diameter of 10 cm used infrequency of 2.4 GHz.Attention: replace the number 2.4 which is by default with the number 2.4 (using a comma). Then convert 10 cmto 100 mm, so that will generate long-tin calculation with 137.76 mm (13.7 cm), and the size ofcans back to the N connector along the 45.92 cm (4.5 cm).
How to assemble the first antenna (N connector)1. Take Socket chassis TNC or N Connector seals that have been put together with copper wire (length
31.5 cm) and cans that have been drilled.2. Input Socket chassis TNC or N Connector seals that have been put together with copper wire into the
hole that had been prepared tin.3. Tighten N Connector with the can using bolt and nut using pliers or hand (if the strong hand.)4. The final form of nuts and bolts work of installation and appearance of copper wire that has been installed
The following step is the step to install the cable to the TNC Plug RG 58 CRMPG
1. Peel the first cable to be connected to the connector. Note carefully, lest there come into the fibrous cord
when inserting the cable into the connector 2. The end result of wiring and installation with N Connector TNC Plug
This step is the final step cans antenna assembly, which combines cable with SMA Connector. Remember that the SMA connector consists of three small objects (needles, bracelets and the connector itself)1. Enter the first metal bands from high school with a cable connector, and then combine cable with
connector2. Insert the needle into the middle of the connector which will serve as a liaison to the WLAN Card. Try
setting the needle is flush with the edge connector for easy mecolokkan connector to the WLAN Card.
Do not enter by force the needle into the plug if it can not. Reduce cable needle to facilitate emasangan
Caution: Be careful when pressing the needle, because it can hurt your fingers, a fine or a broken needle.3. If it is installed properly and fairly sturdy needle, try to plug the tip connector SMA connectors with
WLAN. When installed properly, will look like in the next picture the end result of job creation cans
antenna. Now it's time Plug and Play (Plug and Play)
KoneksidiWindows To be able to connect to Wi-Fi, make sure the services of wireless active, and the driver of the WLAN card is installed. To determine whether these services have been active or not, run services.msc from the run command (use the windows key + R or from the start and select run).Make sure the Wireless Zero Configuration has been active, if not active double-click on Wireless ZeroConfiguration and run the service. Then do the scan to look for signals that can beused.Open the control panel network connection --- --- Wireless Network Connection (select the icon on the WiFi card),then right click on the icon that look like the picture below (click on the tab "WirelessNetworks ".Click on "View Wireless Networks", to display the Wi-Fi signal is detected. In the picturebelow appears to have detected a WiFi which can be reached with the SSID"Smart.Amikom.Yogyakarta".
Click on the SSID is found and Press the "Connect" to launch a WiFi connection kejaringanavailable.
The tools necessary following are the steps that must be prepared before making the antenna cans.
1. A tin that has a 13.3 cm long and 10 cm diameter (grease or oil can also be used).
2. PCMCIA Card (if you use a laptop that has not completed the Wi-Fi 802.11 b or 802.11 g), which has
an external antenna.
3. W-Lan PCI Card Wi-Fi 802.11 b or 802.11 g (for those of you who use a PC, the card is plugged into a
PCI slot). 4. SMA connector (for connecting a cable connector with a PCMCIA card or PCI W-lan
card, usually
some type of PCMCIA is still using the model pigtail with connectors SMA, SMB, SMC or MCX.5. RG-58 coaxial cable whose length should be no more than 15 meters.6. N Plug Connectors (TNC Plug Connector RG 58 CRMPG) used for connecting to a cable.7. N connector (TNC Connector seal chassis).8. Bolts and nuts (to attach to the antenna connector N cans).9. Slabs of the roll diameter brass tube 2.5 to 4 mm, can also use copper wire
taken from electric cables
Preparation Assemble 1. Preparation of the necessary tools close to you and prepare everything properly. 2. Cut your cans if still exceeding 13.3 cm in length using a saw or knife (if there is no hacksaw), and create a hole using a screwdriver or a knife if there is no drill with distance from the edge (bottom of the can) 4.4 cm.
Size used following is the size that you can use to make the antenna cans taken from the site wire.less.dk2. But the needNote that for long cans are not considered here. You can use cans that have alength of more than 100 mm without having to cut
To obtain a more precise measure, you can use the software cantennator which can be downloaded forfree from the internet (use google and then type the keyword "cantennator".Here is an example calculation using the cans with a diameter of 10 cm used infrequency of 2.4 GHz.Attention: replace the number 2.4 which is by default with the number 2.4 (using a comma). Then convert 10 cmto 100 mm, so that will generate long-tin calculation with 137.76 mm (13.7 cm), and the size ofcans back to the N connector along the 45.92 cm (4.5 cm).
How to assemble the first antenna (N connector)1. Take Socket chassis TNC or N Connector seals that have been put together with copper wire (length
31.5 cm) and cans that have been drilled.2. Input Socket chassis TNC or N Connector seals that have been put together with copper wire into the
hole that had been prepared tin.3. Tighten N Connector with the can using bolt and nut using pliers or hand (if the strong hand.)4. The final form of nuts and bolts work of installation and appearance of copper wire that has been installed
The following step is the step to install the cable to the TNC Plug RG 58 CRMPG
1. Peel the first cable to be connected to the connector. Note carefully, lest there come into the fibrous cord
when inserting the cable into the connector 2. The end result of wiring and installation with N Connector TNC Plug
This step is the final step cans antenna assembly, which combines cable with SMA Connector. Remember that the SMA connector consists of three small objects (needles, bracelets and the connector itself)1. Enter the first metal bands from high school with a cable connector, and then combine cable with
connector2. Insert the needle into the middle of the connector which will serve as a liaison to the WLAN Card. Try
setting the needle is flush with the edge connector for easy mecolokkan connector to the WLAN Card.
Do not enter by force the needle into the plug if it can not. Reduce cable needle to facilitate emasangan
Caution: Be careful when pressing the needle, because it can hurt your fingers, a fine or a broken needle.3. If it is installed properly and fairly sturdy needle, try to plug the tip connector SMA connectors with
WLAN. When installed properly, will look like in the next picture the end result of job creation cans
antenna. Now it's time Plug and Play (Plug and Play)
KoneksidiWindows To be able to connect to Wi-Fi, make sure the services of wireless active, and the driver of the WLAN card is installed. To determine whether these services have been active or not, run services.msc from the run command (use the windows key + R or from the start and select run).Make sure the Wireless Zero Configuration has been active, if not active double-click on Wireless ZeroConfiguration and run the service. Then do the scan to look for signals that can beused.Open the control panel network connection --- --- Wireless Network Connection (select the icon on the WiFi card),then right click on the icon that look like the picture below (click on the tab "WirelessNetworks ".Click on "View Wireless Networks", to display the Wi-Fi signal is detected. In the picturebelow appears to have detected a WiFi which can be reached with the SSID"Smart.Amikom.Yogyakarta".
Click on the SSID is found and Press the "Connect" to launch a WiFi connection kejaringanavailable.