1. UTP cable (using belde USA ajah) 25 M or more
2. 4 RJ45 connectors Fruit
3. POE (top and bottom)
4. Outdoor Box 1 pc
5. Pigtail Nmale Nmale to 20 cm, 1 piece
6. Radio Access Point (Wireless-G Broadband Router WRT54GL + 4 Port Switch 802.11b / g)
7. Pipe 3 Metre
8. Briquettes and Box Outdoor Omni Antenna
9. Omni Antenna 15dBi Attach: 1. Replace the first pipe, accidental time pair on the 2nd floor so
rather easy. The standard is actually using the tower
broadcastnya for more leverage. 2. Attach and Box Outdoor Omni Antenna To Pipe. 3. Enter into Box Radio Outdoor AP. and attach
nmale pigtail cable from AP Radio antenna Omni to you. 4. For the POE on the DC there are two cables and RJ45 IN 5. RJ45 input into the Internet and input port also
dc power input into the radio in your ap. both of these cables
taken from the POE on who has been in the previous pairs. 6. Connect the RJ45 cable for 25 m before and connects to the POE
Above. 7. Down To POE POE is basically the same as the Top,
ie there are two wires for power cables from ADAPTOR
ACCESS POINT you and RJ45 (can be from a switch or a
other) 8. Reset your AP then please configure your AP
as a router. (dah first ever writes about the configuration
Radio AP as a router .... Read Here) similar to the way it works
like really. omni antenna installation scheme on more or less like the picture above. Please configuration, if the Radio Access Point Router configuration is complete you then after that further into the process of wardriving (trials to which cover an area of this antenna Weks, yesterday konfignya until breaking the fast. continues after the try was klo many barriers, it does not cover the maximum area (the distance is only 300-500 meters from the antenna If you want maximum must be in pairs at the maximum height to be free from obstructions, then use the grid to menangakap antenna signal from this antenna if you use omni insha allah 15DBi can reach 1-2km
2. 4 RJ45 connectors Fruit
3. POE (top and bottom)
4. Outdoor Box 1 pc
5. Pigtail Nmale Nmale to 20 cm, 1 piece
6. Radio Access Point (Wireless-G Broadband Router WRT54GL + 4 Port Switch 802.11b / g)
7. Pipe 3 Metre
8. Briquettes and Box Outdoor Omni Antenna
9. Omni Antenna 15dBi Attach: 1. Replace the first pipe, accidental time pair on the 2nd floor so
rather easy. The standard is actually using the tower
broadcastnya for more leverage. 2. Attach and Box Outdoor Omni Antenna To Pipe. 3. Enter into Box Radio Outdoor AP. and attach
nmale pigtail cable from AP Radio antenna Omni to you. 4. For the POE on the DC there are two cables and RJ45 IN 5. RJ45 input into the Internet and input port also
dc power input into the radio in your ap. both of these cables
taken from the POE on who has been in the previous pairs. 6. Connect the RJ45 cable for 25 m before and connects to the POE
Above. 7. Down To POE POE is basically the same as the Top,
ie there are two wires for power cables from ADAPTOR
ACCESS POINT you and RJ45 (can be from a switch or a
other) 8. Reset your AP then please configure your AP
as a router. (dah first ever writes about the configuration
Radio AP as a router .... Read Here) similar to the way it works
like really. omni antenna installation scheme on more or less like the picture above. Please configuration, if the Radio Access Point Router configuration is complete you then after that further into the process of wardriving (trials to which cover an area of this antenna Weks, yesterday konfignya until breaking the fast. continues after the try was klo many barriers, it does not cover the maximum area (the distance is only 300-500 meters from the antenna If you want maximum must be in pairs at the maximum height to be free from obstructions, then use the grid to menangakap antenna signal from this antenna if you use omni insha allah 15DBi can reach 1-2km